Home > Hard Drive > Is It Possible To Boot From A IDE Slave Hdd?

Is It Possible To Boot From A IDE Slave Hdd?

Contents

Reply Dave on November 24, 2008 at 1:34 pm Hi I bought this on Ebay, it works realy well, you can connect any hard drive to a usb socket. This allows the cable to select if the drive is master or slave based on the position on the cable. Reply Sue Harris on July 18, 2009 at 7:05 am Hi CliffDid you ever find a solution to your problem installing a new sata hard drive - we're having exactly the If you are adding a second drive, just pick any empty drive bay - one a bit below the current drive might work best, because it will make it easier to http://esecurelive.com/hard-drive/is-a-hd-always-a-master-and-a-dvd-always-a-slave-on-the-same-ide-dable.html

Notcalc (Calculate the wrong answer) Would Trump be worth almost 3x as much if he invested in mutual funds? Any other HDD installed is just another non-boot drive. I can't get these 2 drives to coexist & am wondering what I am doing wrong. That way it can draw twice as much power, and get the HDD running. you could try here

How To Connect Ide Hard Drive To Sata Motherboard

If you have this backwards the drive will normally either be silent or fail to power up. Thanks for the info. Click here to join today! Wanted to install in new box.

In addition I had to purchase a PCI serial ATA host controller card with a cable to connect the new HD. It really is advised in your case to make the HDD the port Master, and the optical unit the Slave, when they share one IDE port and cable. The WD has no jumper config for slave. How To Make Ide Boot Instead Of Sata solved How to Set New SSD to be Boot Drive (with Another SSD and HDD to be Slave)?

This drive will be the main drive, but not until I load the image from the old drive. By the four sentence, you are assuming that everyone reading this will understand what ‘jumpers' are. I have a spare one which i utilize as of time while awaiting for its replacement. This Site So, what to do?(a) disconnect both HDD and optical units.

If not, select the auto-detect option. Ide Hard Drive Jumper Settings I have a Windows XP system. On some machines, by default IF there is an IDE drive installed the mobo tries to use it for booting, and you need to prevent that. Once reported, our moderators will be notified and the post will be reviewed.

Sata And Ide Hard Drives Together

Some may argue that people like me who may find it easy to understand, why shouldn't the newbies? http://en.community.dell.com/support-forums/disk-drives/f/3534/t/19361896 share|improve this answer edited Sep 13 '12 at 18:04 answered Sep 11 '12 at 8:16 aliasgar 3,3711525 1 Just a brief note: These jumper settings can differ per manufacturer. –Hennes How To Connect Ide Hard Drive To Sata Motherboard The Hard Drive only came with a CD, no floppy disk. Ide And Sata Drives In Same Computer If your drives are showing up properly then you did it right.

Reply cher on August 21, 2007 at 5:30 am The instructions are great and have saved my sanity and hours of trying to start my computer in Dos when i do Hope you can help, so far this has been a longwinded exploraton of my computer. One has a red strip for wire one and the other a pink strip. 5 answers Last reply Jun 17, 2013 Best Answer May 10, 2013 More about booting seconday slave Reply Robert on October 25, 2008 at 3:50 pm Great Article. Motherboard With Ide And Sata Ports

Set bios.1/3 of highway deaths are caused by drunks. Reply vince on March 26, 2013 at 2:21 pm for one if the NEWB reads this it will perk his interest. Verify the drive is enabled in system BIOS. far from a computer expert I was able to use your information to find the missing step I needed to install my sata 2nd drive.

thanks Reply Jenna on March 20, 2009 at 1:22 pm Okay… here is my issue and I am at whits end.My hard drive crashed, but I had a back up one. What Are The Two Goals When Implementing A Raid Solution You simply highlight the drive you want the hit enter. and my standard ATA100 drive is a secondary.

Thanks, hope to hear from you or another one of the commenters soon.

Copyright 1990-2003 Dell Computer Corp. Set another device, like a floppy drive, to boot from. You will be prompted during the first part of setup to partition and format your drive; if you are using Windows 2000, XP or Vista, make sure to use the NTFS How Many Hard Drives Can Be Connected To A Single Ide Cable I do not, however, have a long enough power cable for the new HD.

And here one thing to note is that it is preferred to have the CD-ROM and other non-hard drive products on the secondary ATA channel. Flag Permalink This was helpful (0) Collapse - Mixing SATA and IDE drives in a system? However, when I loaded XP the icons did not appear and I no programs are on the hard drive. Roberts on January 13, 2010 at 7:40 pm I run with windows 7 and use SATA HD When I installed a hard drive ( a have a couple of drives installed

Read more. Thanks in advance! I'll double check the motherboard drivers but I'm sure the one's I've got are up to date. My HDD has a Windows XP Pro Installed in it prior the crashed of motherboard.

I knew the new drive was there and installed correct as I could find it in bios as well as the hardware manager.I did need to explore a little after using successfully installed second hard drive thanks to this post 🙂 Reply Joe on August 23, 2009 at 11:14 am I have a 320 gig IDE hard drive .Im trying to install This is because some older optical units do a poor job of filling the Master role. It does not recognise the difference in size.

The problem of reinstalling Windows on a SATA boot device still happens with XP, but almost the first message from Windows asks you to "press F6 to install a Raid controller". Change any necessary jumpers (see "Setting Jumpers" above) so that both drives as well as a CD drive are recognized. Very helpful!! Reply Janna on August 27, 2007 at 3:26 pm I have a problem!

All Rights Reserved. Reply Glenn on November 7, 2007 at 2:59 am Steve - if all is connected then u must format - see above under ‘Software Installation/Cloning'I've just added a second and had