Home > Is It > Is It Power Prob Or IDE Issue?

Is It Power Prob Or IDE Issue?

I could be wrong, though.It could be that the logic board of the HDD is failing. If you're reading this book after your old hard disk has been packed off to the manufacturer for replacement, we can still help. Replace the power cable with one that you know works. USB Port disabled. weblink

It can either be a physical issue like power not getting to the drive or a IDE / SATA cable has come unplugged. If your beep code is not listed, continue troubleshooting. Test and did not work.6). Test and works. https://www1.imperial.ac.uk/publichealth/departments/ide/it/troubleshooting/hardware/

Check into Administrative Tools> services ."What specific services are you talking about? Reply Doug November 18, 2009 at 5:27 pm There may be (another) problem if you're running Vista; there are 2 versions of it that don't come with DVD codecs, even if How do I find out what's missing? Only 6-wire 1394a ports can power a 1394 drive; 4-wire ports do not provide power.

ScribelsJul 29, 2011, 10:16 AM Update: It did it again. Test the system to see if the problem is corrected, and continue to the next step if the problem is not corrected. Go get a paper clip and straighten it out. In some situations, you may be able to temporarily get the computer to boot.

Remove the CD-ROM from adapter and connect to DVD burner. If this resolves your irregular POST or generates error messages, reconnect each device until you determine which device or cable is causing the issue. Connector 1 is the video connector permanently connected to the system board. have a peek here Confused, I tried restarting my computer several times with the same problem each time.

What do I do next? Drive not powered on. Read More ) determines which partition to load, based on data it reads from the boot loader. Correct heat sink installation is required for proper cooling.

Only 1 is enabled by default. https://support.lenovo.com/us/en/documents/migr-4xvqal These instructions can be used for both internal and external drives but some of the fundamentals might be a little different. Then, disconnect any IDE, SATA, SCSI, or other data cables from the motherboard. I reconnected the SATA and the power cable for my SSD but still no luck.

Then again, dealing with computers that would still not rule out anything. If the ailing hard disk is an additional drive, such as an external hard disk, it won't show up in My Computer or Windows Explorer and you'll see a "Missing Shortcut" How to Fix a Windows Blue Screen of Death BSODs can occur because of either hardware or software problems. Then I go to device manager and Scan for Hardware changes it shows up.

Can't Copy or Drag and Drop Files to CD-R or CD-RW Media 689 I can't read CD-RW media in the target computer. Detecting ide drives Detecting IDE drives PC not detecting IDE hard drives How to detecting IDE drives Boot Problem on detecting IDE drives detecting IDE drives .x.? - WTF? This will zero the HDD completely, like a factory-form reset. What Is UEFI And How Does It Keep You More Secure?

I’ve covered troubleshooting motherboard problems 3 Troubleshooting Tips Guaranteed to Boot Your PC's Motherboard 3 Troubleshooting Tips Guaranteed to Boot Your PC's Motherboard This article covers basic motherboard troubleshooting methods, common faults Caution: Some of the steps below recommend removing physical parts from inside the computer. You will use this disk to repair or diagnose your operating system.

In your case, the problem almost certainly relates to indiscriminate use of a data backup and recovery solution, which damaged your operating system’s software.

But that's me; as they say, your mileage may vary. If a fan has failed (especially the heat sink fan for the CPU), your computer could be overheating or detecting the fan failure, causing the computer not to boot. Connections frequently become loose when the computer is moved. It did say for last night "The device, \Device\Ide\IdePort0, did not respond within the timeout period".

Hit F2 go to BIOS and Drive Configuration shows "SATA Port 0: ATPAI DVD A D-ATAPI" (why??). From experience, most errors like this do come from registry issues, or if the drive is really dead. Introduction to beep codes Beep codes are an important and useful tool when troubleshooting booting issues. Try These Tips Windows 8 Refresh Not Working?

The most effective of these is the deep reset, which temporarily halts power to the volatile memory on board all computers, thus resetting it to a factory fresh state. So what I'm gathering from this, is you want me to test the 4 pin connectors? All submitted content is subject to our Terms of Use. This condition will and or can result in a "Non-system disk" error.

Return to the Imperial homepageResearchCoursesFaculties & Departments CampusLife2 News & EventsAdmin & ServicesAbout ImperialPeopleFor:Prospective StudentsStudentsAlumniStaffBusinessMediaSchool of Public HealthAbout usDepartmentsEducationPeopleNewsEventsContact usEarly Career Researcher AwardsGeneral Hardware IssuesIf you need assistance with any of Can't Change Contents of Floppy Disk 695 I can't read a disk in the floppy drive. Today I’d like to walk... If the system works after the devices are removed, the issue may be compatibility with the new hardware.

Just as you checked the power, check the connectors. Or you could just get that PSU from the store and see if it fixes your problem. After selecting the program, and clicking through a confirmation window, choose the flash drive as your target for the recovery  drive and select next. Follow me on my Twitter profile.

Finally what I did was go into Device Manager, clicked disk drives and "Scan for Hardware changes" And once I did that it actually showed up. I have tried switching the SATA cable but no luck with that method as well. some ssd had power on bricking issues. Check the brightness & contrast levels of the monitor via the menu button, to make sure it has not been set too dark.

by R. Modern processors get very hot and must be cooled properly. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). If all else fails and you cannot shutdown/restart your computer, then hold down the power button on the machine until it forcibly turns off.